Key takeaways
- Choose a compatible category before entering a value and selecting the two units.
- Temperature requires offsets; area requires squared length factors.
- KB and KiB, US and Imperial gallons, and local land measures are separate conventions.
The unit converter translates a number between compatible measurement units. It covers length, area, weight, volume, temperature, speed and data sizes. Use it when reading a specification, comparing quantities expressed differently or preparing a calculation that requires consistent units.
A conversion changes the representation of a quantity. It does not validate the original measurement or improve its precision. If a room was measured only approximately, a long converted decimal remains an approximation. Keep the source unit and measurement context alongside any number you copy into a report or spreadsheet.
Before you start
Identify the kind of quantity first. Square metres belong to Area, metres belong to Length, and cubic metres belong to Volume. A number by itself cannot tell the converter whether you measured a side, a floor or a container. Choosing the wrong category can give an apparently plausible answer to a different question.
Read the unit labels carefully. The tool uses international feet and pounds, and its ounce is avoirdupois rather than troy. Volume options distinguish the US liquid gallon from the Imperial gallon. Data options distinguish decimal prefixes, such as KB, from binary prefixes, such as KiB. These choices are explicit rather than inferred from your location.
Bigha, guntha and tola are omitted because an exact official factor was not verified for this implementation. Do not substitute an acre or a pound for a locally named unit without checking the applicable authority and context. A familiar conversion from another region is not sufficient evidence for an official record.
Step by step with CrizaTools
- Open Unit Converter and choose Category. The available From and To units change to match it.
- Enter Value as a finite number without unit letters. Use a decimal point when a fractional value is required.
- Choose From, the unit used by the entered value.
- Choose To, the unit you want to read. The converted value updates automatically.
- Press Swap units if you want to reverse the direction. The entered number stays the same while the unit choices exchange places.
- Read the source and destination labels beneath the result. Use Copy to copy the numeric output, then record its unit in the receiving document.
When you change category, check the new default units before continuing. A number retained from an earlier category does not acquire a meaningful physical interpretation automatically. For example, the number 32 can be a temperature in one scenario and a length in another; it is your responsibility to specify which quantity you intend.
Two worked examples
Example 1: one acre expressed in square metres. Select Area, enter 1, choose Acre under From and Square metre under To. The factor used is 4046.8564224 square metres per acre, so the result is 1 × 4046.8564224 = 4046.8564224.
The displayed numeric result uses up to twelve significant digits, so the interface may round the last digits. To reverse the same physical quantity, enter the square-metre value after swapping. Pressing Swap units alone keeps the entered number at one, which asks for one square metre expressed in acres; that is a different conversion scenario.
Example 2: freezing-point temperature. Select Temperature, enter 32, choose Fahrenheit under From and Celsius under To. The formula is (F − 32) × 5/9. Substituting 32 gives (32 − 32) × 5/9 = 0, so the output is 0 °C.
Changing To to Kelvin gives 273.15 K. Multiplying Fahrenheit by a scale without subtracting the offset would give an incorrect result. The same logic explains why −40 °C and −40 °F represent the same temperature: −40 × 9/5 + 32 = −40. The converter rejects temperatures below absolute zero.
Limits and what to watch for
Multiplicative categories use value × source factor ÷ destination factor. Each unit factor refers to the category’s shared base, such as metres, square metres or bytes. Temperature follows separate affine formulas. The NIST SI guide provides conversion guidance and tables; checked 16 November 2026.
Area conversion requires the square of a length factor. A foot is 0.3048 metres, while a square foot is 0.3048² = 0.09290304 square metres. Do not multiply an area by 0.3048 alone. Similarly, a volume scale generally uses a cubed length relationship when converting cubic units.
For data, this interface defines KB as 1000 bytes and KiB as 1024 bytes. MB and GB use powers of 1000, while MiB and GiB use powers of 1024. A bit is one eighth of a byte. NIST explains the distinction in its binary prefixes reference; checked 16 November 2026. Always compare storage quantities using the same convention.
Arithmetic uses JavaScript floating point numbers and the display is rounded to twelve significant digits. Extremely large results can overflow and are rejected. This is a practical conversion tool rather than an arbitrary-precision measurement system. Use precision and rounding appropriate to the source measurements, especially where the original value has only two or three reliable digits.
Common mistakes
- Choosing Length when the measurement is an area.
- Assuming all gallons have the same volume.
- Treating Swap units as a full round-trip conversion of the displayed quantity.
- Entering
5 kginstead of the numeric value5. - Reading a binary memory quantity as a decimal storage quantity.
- Applying an unsourced traditional-unit factor to a formal land or weight record.
Questions and answers
Why is a temperature conversion not simple multiplication?
Celsius and Fahrenheit use different zero points. The converter applies both a scale and an offset. Kelvin also has a different zero point from Celsius, even though their unit increments have the same size.
Does Swap units replace the input with the last answer?
No. It exchanges From and To while preserving the entered numeric value. To convert the last answer back, copy that number into Value after swapping and check both labels.
Can I convert kilograms directly to litres?
No. Mass and volume are different categories. Relating them requires the material’s density and appropriate conditions. The tool does not guess that extra information from the number you enter.
Are the displayed digits all measurement precision?
No. They show a rounded numerical conversion. Your source measurement determines meaningful precision. A rough one-acre estimate remains rough even when its converted value includes many decimal places.
Why are local land and traditional weight units missing?
This version omits bigha, guntha and tola without a verified exact official factor. Check the relevant authority and region before making a formal conversion, rather than relying on an unattributed internet table.
Sources
- NIST: Special Publication 811, checked 16 November 2026.
- NIST: prefixes for binary multiples, checked 16 November 2026.
Use the unit converter for compatible measurements and the percentage calculator for proportional changes.
Free tools for this
Calculators
Unit Converter
Convert length, area, weight, volume, temperature, speed and data sizes.
Calculators
Percentage Calculator
Four percentage calculators in one: X% of Y, what percent X is of Y, percentage increase or decrease, and adding or taking off a percentage.
Calculators
BMI Calculator
Calculate adult BMI in cm and kg or feet and pounds. Compare WHO international categories with Asian cut-offs from Indian Ayush guidance, clearly labeled.